Passive house: the forgotten detail that takes years
Hello, Quentin here.
The detail that can cost years of rework is the continuity of airtightness, checked before closing up the walls.
In a passive house, a small leak can degrade energy performance and promote humidity. The problem is often hidden at the joints between walls, windows and the roof.
Identifying it on the plans, then verifying it on site, costs far less than reopening walls after occupancy.
Do it without delay
- Identify sensitive junctions between walls, windows, roof, and the ground floor on the plans.
- Request a detailed drawing of each joint before the start of construction.
- Choose someone responsible for maintaining airtightness.
- Plan a blower-door test before the finishes mask the defects.
- Have each leak corrected, then verify the result before handover.
To understand the traps that undermine a project, also consult these tips on the defect that can block a passive-house project and on the design detail that affects summer comfort.
The airtightness defect that escapes the plans
The common error is to treat airtightness as a product to be installed rather than as a continuous line to be created. A high-performance membrane is not enough if its joints around ducts, windows, or beams remain imprecise.
These leaks allow warm, moist air to circulate inside the walls. In the long run, they can promote condensation, reduce the effectiveness of thermal insulation, and complicate repairs.
Why joints matter as much as insulation
A passive house rests on several complementary elements: thermal insulation, limiting thermal bridges, and well-tuned double-flow ventilation. If air passes through poorly executed joints, the whole system loses coherence.
Bioclimatic design helps reduce heating needs, while thermal inertia contributes to stabilizing the temperature. But neither one nor the other makes up for a perforated envelope: the quality of execution protects indoor comfort and the building’s durability.
Passive house: comparing an invisible defect with an early correction
Let’s imagine Léa and Sami, who are building a passive house. At an initial inspection, a leak appears around a duct crossing the ceiling: the defect is still accessible and can be corrected with an appropriate connector.
If the same leak is discovered after the ceiling is installed, sometimes part of the finishes must be dismantled, its origin traced, and the inspection redone. The cost depends on the project, but the right moment to intervene is before closing up the walls.
| Moment of inspection | What it enables | Probable consequence |
|---|---|---|
| Before finishes | Localize and repair leaks while the joints are accessible | Targeted intervention and a simpler site |
| After occupancy | Confirm a problem already present in the envelope | Longer search and possible dismantling |
Checking airtightness in 3 steps
1. Draw a continuous line on the plans
Ask the project manager to clearly represent the airtight layer around the entire envelope. Each interruption must have a detailed solution, especially at the joints between joinery, walls and the roof.
2. Check critical points before closing
On site, check cable and duct passages, as well as the window junctions. An intermediate test helps locate leaks while the materials remain accessible.
3. Correct, test and keep the results
Have the identified defects repaired, then request a new inspection according to the project requirements. Keep the detail drawings and the reports: they facilitate the monitoring of the house and any subsequent intervention.
Frequently asked questions about airtightness in a passive house
What is the detail most often forgotten in a passive house?
The continuity of airtightness at the joints and around penetrations is often underestimated. The plans must specify how each connection will be made.
When should a blower-door test be performed?
An inspection before finishes allows locating and correcting leaks when the joints are still accessible. A final inspection can then verify the project’s result.
Does airtightness prevent air renewal?
No. An airtight envelope limits uncontrolled leaks. Double-flow ventilation ensures the controlled renewal of the air, provided it is correctly installed and maintained.
Are thermal bridges the same thing as an air leak?
No. A thermal bridge is a zone where heat transfers more easily through the envelope. An air leak corresponds to an uncontrolled air passage. The two can coexist at a poorly designed junction.
Thank you for reading! I would be happy to hear your opinion in the comments. — Quentin







